Features:
The Naza-M V2 is a powerful flight controller for enthusiasts, as well as commercial and industrial flyers. It is easy to install, simple to configure, and extremely stable.
All-In-One Compact Multi-Rotor Autopilot System
Supports 9 Different of Multi-Rotor Configurations, Ideal for DJI F450/F550 and E Series Tuned Propulsion Systems
New Assistant Software for Smartphones
Free Ground Station
Take-Off Assistance
Multiple Flight Control Modes and Intelligent Switching
GPS Module Available for Accurate Position Stabilization
Intelligent Orientation Control (IOC)
Supports General, PPM, and S-Bus Receivers
Arm/Disarm Modes for Safe Motor Starting
2-Axis Gimbal Stabilization
Two Levels of Low Voltage Warnings and Protection
Single Motor Failure Protection
Supports Remote Gain Adjustment from the Transmitter
Enhanced Failsafe Features, Including Auto Return-to-Home
Compatible with DJI Video Downlink, iOSD, Ground Station, ZH4-3D/H3-3D Gimbals, and Future Products
Technical Specifications:
| Basic Performance | Supported Multi-Rotor | Quad-rotor I4, X4 |
| Hex-rotor I6, X6, IY6, Y6 |
| Octo-rotor I8,V8,X8 |
| Supported ESC Output | 400Hz refresh frequency |
| Recommended Transmitter | PCM or 2.4GHz with minimum 4 channels |
| Working Voltage Range | MC:4.8V~5.5V |
| VU Input: 7.4V ~ 26.0 V |
| (recommend 2S ~ 6S LiPo) |
| Output(V-SEN port red wire): 3A@5V |
| (burst current:7.5A) |
| Power Consumption | MAX: 1.5W(0.3A@5V) |
| Normal:0.6W(0.12A@5V) |
| Operating Temperature | -10°C ~ 50°C |
| Assistant Software System Requirement | Windows XP sp3 / Windows 7 / Windows 8 |
| Flight Performance | Hovering Accuracy(GPS Mode) | Vertical:±0.8m |
| Horizontal:±2.5m |
| Max Yaw Angular Velocity | 200°/s |
| Max Tilt Angle | 35° |
| Ascent / Descent | 6m/s,4.5m/s |
| Hardware | Weight | MC:27g |
| PMU:28g |
| GPS:27g |
| LED:13g |
| Dimensions | MC: 45.5mm x 32.5mm x 18.5mm |
| PMU: 39.5mm x 27.5mm x 10.0mm |
| GPS & Compass 46mm(diameter)x10mm |
| LED: 25mm x 25mm x 7.0mm |
| Built-In Functions | Multiple Autopilot Control Mode |
| Enhanced Fail-safe |
| Low Voltage Protection |
| S-Bus Receiver Support |
| PPM Receiver Support |
| Independent PMU Module |
| 2-axle Gimbal Support |
Packing list:
Naza-M V2 × 1
GPS Module × 1
FAQ:
Hardware Install Questions
1.Does it support multicopters with only 3 propellers included?
No, it doesn't.
2.Does it support Spectrum transmitters and receivers?
Yes, it does.
3.Do I need to use BEC power seperated in order to power the MC?
No need, VU already includes BEC function.
4.Can I use Y wire to connect two motors?
In principle, one MC port connect to one ESC and one motor.
5.What can I do, my aircraft always drifts forward?
Never move aircraft within 5s after power it on. No trim in your transmitter.
6.Low-Voltage Warning is available in manual mode or not?
Yes,Low-Voltage Warning is available in manual mode.
7.Arming makes motors tune too fast or too slow, what can I do?
Please change Motor Idle Speed through assistant software.
8.Please explain why computer doesn't recognize USB device?
Make sure driver has been installed sucessfully, PMU should be connected to LED port of MC, not Ext port.
9.Which OSD can support NAZA?
NAZA has no OSD function, 3rd part OSD product can be used.
Basics
1.What's the difference between NAZA-M Lite/NAZA-M V1/NAZA-M V2?
Click Here for Detailed Information.
2.Can NAZA-M be used on helicopters?
No,It can't be used on helicopter.
3.Why is my NAZA-M not stable in a low-temperature environment?
Place your aircraft outside for minutes firstly.
4.What's the usage of NAZA-M EXT port?
Used for GPS Module.
5.Does NAZA-M support PPM receiver?
Yes, it does.
6.Some aircrafts with Naza installed drift a lot, and some are very stable. Why is that?
You can not have position lock without Naza GPS module. The flight performance will affected a lot by the environment,such as windy condition, mechanically setup, center of gravity, etc.
7.When my Naza takes-off in attitude mode it drifts to one side, why?
Please check the motors and ESCs. It is also possible that the NAZA sensor error is too big, please connect to the assistant software and calibrate the IMU.
8.When I push the throttle stick the Nana-M is not responding, why?
In order to prevent faulty operation, you need to execute CSC. Please check the user manual for detailed instructions.
9.When I execute CSC, motors are not responding, why?
Please observe the LED flashing status.
Four yellow flashes means preheating, and after preheating it will be OK.
Four green flashes means there is a sensor error, please connect to the assistant software and calibrate the IMU.
Four red flashes means the sticks are not in center position, please connect the software and calibrate the transmitter.
10.The LED lights are flashing normally, but when I execute CSC, motors still have no response?
Please check the power supply connection.
Please check the transmitter stick commands and its channel mapping in the software, it has to be consistent and makes full range sliding. Also check the throttle and pitch channel mapping.
11.Why does the LED flash yellow & red continuously after power on?
It means the compass has been compromised, please calibrate the compass.
12.Can I use the LED/GPS of V2 on V1 or Lite?
No, you cannot.
The LED flashes red & yellow & green continuously, the software indicates ERR 25 and the acceleration
13.show ERROR, the aircraft cannot take off?
The internal sensor may break down because of collision. Please contact local dealer for after-sales service.
14.It asked me for SN after I install the assistant software, where can I get the SN?
The SN has already been entered, no need to input again. This is because you did not connect the main controller or you did not install driver correctly.
15.I followed the instruction to register, but I have not received any activation email?
Please confirm your email address is correct or check the spam mail.
It is recommended to use Gmail, hotmail, etc for registration.
16.After I assembled the aircraft and flight controller, every time I try to take-off it flips away?
Please read the user manual carefully, this may be caused by incorrect installation. Please check:
1. the orientation of the main controller;
2. the rotate direction of the motor and propeller;
3. the ESCs are in the correct port;
4. set the correct mixer type in the software;
17.The aircraft is circling around when hovering, and the circle is getting bigger and bigger, I almost lost control of it?
The compass has been compromised. Please calibrate the compass. If the problem cannot be solved, please refer to the user manual 'Toilet Bowl Effect'.
18.Why the yellow light is still blinking when I switch to GPS mode?
The main controller failed to identify the GPS &compass module. Please check the connection.
Software Settings Questions
1.Does the Assistant software support Mac?
No, currently it only works on Win XP, Win7, Win8.
2.After registering with Assistant Software, I still can't log in?
Please log in your emial box, and click the link to activate the register firstly, then you can enter the software with the email and password to log in.
3.What can I do when software and main controller can't be connected?
The assistant driver has not been installed sucessfully. With MC powered firstly, USB cable connected, then install the driver.
4.How to deal with the configuration error?
Please calibrate your transmitter sticks and then restart MC.
5.No reaction from motors during arming, what should I do?
Please refer detailed instructions in the manual. Start software to check if the control stick on your transmitter can reach the full range, directions are correct or not. Please unplug USB when you do the testing.
6.Flight Parameters recommended for Flame Wheel F550?
Default parameters are 100% normally, but it can be adjusted according to actual flight conditions and different control feeling.
7.How to set up 3-switch for flight control mode?
Connect switch channel to U channel of MC, use Trim menu to adjust 2nd switch to Atti. Mode, use End Point to adjust 1st and 3rd switch for Manual mode and GPS mode.
8.How to set up Fail-Safe?
Make sure all channels of your transmitter include Fail-Safe, adjust any one of the 3 switch control modes to Fail Safe mode, then record the position value in Fail Safe of your Tx. After that, switch to other control mode and turn off the transmitter, assistant software show it jumps into Fail Safe mode and meantime LED shows blue ligh, setup is done.
9.How to match propellers and motors?
Very important to match Props and motors to get good flight performance. 900KV motor matching 8-10 inches Props are recommended.
10.My Red LED is flashing quickly, what is the problem?
Connect MC with software to check what problem is and then find out a corresponding solutions.
11.Where should the main controller be placed?
MC has to be installed close to C.G. No need any damping, just use 3M double-side sticker.
12.What mode should be used in Transmitter?
Set your model type as Airplane.
13.Does the software support Vista OS?
Yes, it does.
14.The height can't be locked, why?
Adjust vertical gain, use defaul throttle curve and 50% throttle for hovering.
15.Why my Windows 7 OS cannot install the assistant software driver successfully?
Some of the users who use WINDOWS 7 operating system may not have the usbser.sys file, please download this file and put it into C: \ WINDOWS \ system32 \ drivers, and then reinstall the driver.
Download the usbser.sys file.
1. About us
Shenzhen Weida Trade Co. Ltd is a well-known excellent company, For a long time, we are committed to providing all kinds of auto parts and electronic products for the global customers. In recent years, with the progress of science and technology, the UAV industry is developing rapidly, the rapid emergence of a variety of UAV in the global market. Among them, DJI company's products from China has occupied the global market share of 70%, Has been favored by consumers around the world. So We carry out business cooperation with the agents of DJI Corp, began to the world's UAV distributors and UAV enthusiasts to provide DJI UAV and UAV accessories. We sell the DJI UAV and accessories are brand new genuine, 100% from DJI company's own factory production, good quality. We adhere to the "quality first, customer first, service first" business philosophy, with first-class products and services, to create greater value for our customers, we are willing to work with customers hand in hand, towards a better tomorrow.
2. Transaction details
About the price: we will give you the best price according to the quantity of your order, the greater the order, the lower the price.
Terms of payment: the first transaction, the first payment and then shipped.
In the later transaction, when you pay 50% of the payment, we will be able to ship the goods.
Payment method: L / C, T / T, Western Union
Product packing way: in the original outer packing box outer layer and then a carton packaging, better protect your products.
Transport: small orders using EMS, UPS, DHL, FedEx, TNT and other courier, large quantities of orders using air or sea.
Delivery time: shipment within one week after receipt of payment, and notify you.
Delivery time: Express delivery and air transport: after delivery a week or so the arrival,Ocean Shipping: after delivery a month or so the arrival.
Notice: If your order is worth more than $500, we will give you free shipping.
3. After sales service policy
Our after-sales service policy is the same as DJI company, you can visit the DJI company's official website (http://szweida.en.made-in-china.com) to get a detailed understanding of. If your product has a problem, you can find DJI Service Center in your country, if your country don't have the DJI company's repair center, you can couriered the products to us to deal with.
If you have any questions or suggestions about our products and price and service, please contact us as soon as possible, you can use the Email and TradeMessenger or Wechat, we will be very welcome and appreciate your patronage.
Tel: +86-0755-33558650, +86-15986683828
Email: 379560659@qq.com, tianyiyiyunhangpai@163.com
WeChat: WZDHXNYM56370 QQ: 379560659
){kind=link}